Posts Tagged ‘zaatakować wiór bin’

PostHeaderIcon Attack IC LPC2119FBD64 Firmware

Attack IC LPC2119FBD64 Firmware

Attack IC LPC2119FBD64 Firmware

We can Attack IC LPC2119FBD64 Firmware, please view below IC LPC2119FBD64 features for your reference:

16/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package.

16 kB on-chip Static RAM.

128/256 kB on-chip Flash Program Memory. 128-bit wide interface/accelerator enables high speed 60 MHz operation. In-System Programming (ISP) and In-Application Programming (IAP) via on-chip boot-loader software. Flash programming takes 1 ms per 512 byte line. Single sector or full chip erase takes 400 ms

EmbeddedICE-RT interface enables breakpoints and watch points. Interrupt service routines can continue to execute while the foreground task is debugged with the on-chip RealMonitor™ software.

Embedded Trace Macrocell enables non-intrusive high speed real-time tracing of instruction execution

Two interconnected CAN interfaces with advanced acceptance filters.

Four channel 10-bit A/D converter with conversion time as low as 2.44 µs.

Multiple serial interfaces including two UARTs (16C550), Fast I2C (400 kbits/s) and two SPIs 60 MHz maximum CPU clock available from programmable on-chip

Phase-Locked Loop with settling time of 100 µs.

Vectored Interrupt Controller with configurable priorities and vector addresses.

Two 32-bit timers (with four capture and four compare channels), PWM unit (six outputs), Real Time Clock and Watchdog

Up to forty-six 5 V tolerant general purpose I/O pins. Up to nine edge or level sensitive external interrupt pins available.

On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz

Two low power modes, Idle and Power-down.

Processor wake-up from Power-down mode via external interrupt.

Individual enable/disable of peripheral functions for power optimization.

Dual power supply:

CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ±0.15 V).

I/O power supply range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads.

PostHeaderIcon Break Chip ATmega48PA Heximal

Break Chip ATmega48PA Heximal

Break Chip ATmega48PA Heximal

We can Break Chip ATMEGA48PA Heximal, please view below Chip ATMEGA48PA Features for your reference:

· High Performance, Low Power AVR® 8-Bit Microcontroller

· Advanced RISC Architecture

– 131 Powerful Instructions – Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 20 MIPS Throughput at 20 MHz

– On-chip 2-cycle Multiplier

– 4/8/16/32K Bytes of In-System Self-Programmable Flash progam memory (ATmega48PA/88PA/168PA/328P)

– 256/512/512/1K Bytes EEPROM (ATmega48PA/88PA/168PA/328P)

– 512/1K/1K/2K Bytes Internal SRAM (ATmega48PA/88PA/168PA/328P)

– Write/Erase Cycles: 10,000 Flash/100,000 EEPROM

– Data retention: 20 years at 85°C/100 years at 25°C(1)

– Optional Boot Code Section with Independent Lock Bits

In-System Programming by On-chip Boot Program

True Read-While-Write Operation

– Programming Lock for Software Security

Peripheral Features

– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode

– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode

– Real Time Counter with Separate Oscillator

– Six PWM Channels

– 8-channel 10-bit ADC in TQFP and QFN/MLF package

Temperature Measurement

– 6-channel 10-bit ADC in PDIP Package

Temperature Measurement

– Programmable Serial USART

– Master/Slave SPI Serial Interface

– Byte-oriented 2-wire Serial Interface (Philips I2C compatible)

– Programmable Watchdog Timer with Separate On-chip Oscillator

– On-chip Analog Comparator

– Interrupt and Wake-up on Pin Change

Special Microcontroller Features

– Power-on Reset and Programmable Brown-out Detection

– Internal Calibrated Oscillator

– External and Internal Interrupt Sources

– Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages

– 23 Programmable I/O Lines

– 28-pin PDIP, 32-lead TQFP, 28-pad QFN/MLF and 32-pad QFN/MLF

Operating Voltage:

– 1.8 – 5.5V for ATmega48PA/88PA/168PA/328P

Temperature Range:

– -40°C to 85°C

Speed Grade:

– 0 – 20 MHz @ 1.8 – 5.5V

Low Power Consumption at 1 MHz, 1.8V, 25°C for ATmega48PA/88PA/168PA/328P:

 

Programmable Flash

ATmega48PA

ATmega88PA

ATmega168PA

ATmega328P

– Active Mode: 0.2 mA

– Power-down Mode: 0.1 µA

– Power-save Mode: 0.75 µA (Including 32 kHz RTC)