Break IC, Recover MCU, Microcontroller Reverse Engineering

Posts Tagged ‘recover chip source code’

Recover Chip MC9S08DZ32ACLC Firmware

We can Recover Chip MC9S08DZ32ACLC Firmware, please view below the Chip MC9S08DZ32ACLC features for your reference:

8-Bit HCS08 Central Processor Unit (CPU)

· 40-MHz HCS08 CPU (20-MHz bus)

· HC08 instruction set with added BGND instruction

· Support for up to 32 interrupt/reset sources

On-Chip Memory

· Flash read/program/erase over full operating voltage and temperature

— MC9S08DZ60 = 60K

— MC9S08DZ48 = 48K

— MC9S08DZ32 = 32K

— MC9S08DZ16 = 16K

· Up to 2K EEPROM in-circuit programmable memory;

8-byte single-page or 4-byte dual-page erase sector;

Program and Erase while executing Flash; Erase abort

· Up to 4K random-access memory (RAM)

Power-Saving Modes

· Two very low power stop modes

· Reduced power wait mode

· Very low power real time interrupt for use in run, wait, and stop Clock Source Options

· Oscillator (XOSC) — Loop-control Pierce oscillator;

Crystal or ceramic resonator range of 31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz

· Multi-purpose Clock Generator (MCG) — PLL and FLL modes (FLL capable of 1.5% deviation using internal temperature compensation); Internal reference clock with trim adjustment (trimmed at factory, with trim value stored in flash); External reference with oscillator/resonator options in the process of Copy microcontroller

System Protection

· Watchdog computer operating properly (COP) reset with option to run from backup dedicated 1-kHz internal clock source or bus clock

· Low-voltage detection with reset or interrupt; selectable trip points

· Illegal opcode detection with reset

· Illegal address detection with reset

· Flash block protect

· Loss-of-lock protection

Peripherals

· ADC — 24-channel, 12-bit resolution, 2.5 ìs conversion time, automatic compare function, temperature sensor, internal bandgap reference channel

· ACMPx — Two analog comparators with selectable interrupt on rising, falling, or either edge of comparator output; compare option to fixed internal bandgap reference voltage.

· MSCAN — CAN protocol – Version 2.0 A, B; standard and extended data frames; Support for remote frames; Five receive buffers with FIFO storage scheme; Flexible identifier acceptance filters programmable as: 2 x 32-bit, 4 x 16-bit, or 8 x 8-bit

· SCIx — Two SCIs supporting LIN 2.0 Protocol and SAE J2602 protocols; Full duplex non-return to zero (NRZ); Master extended break generation; Slave extended break detection; Wakeup on active edge.

· SPI — Full-duplex or single-wire bidirectional; Double-buffered transmit and receive; Master or Slave mode; MSB-first or LSB-first shifting

· IIC — Up to 100 kbps with maximum bus loading; Multi-master operation; Programmable slave address; General Call Address; Interrupt driven byte-by-byte data transfer

· TPMx — One 6-channel (TPM1) and one 2-channel (TPM2); Selectable input capture, output compare, or buffered edge-aligned PWM on each channel.

· RTC — (Real-time counter) 8-bit modulus counter with binary or decimal based prescaler; Real-time clock capabilities using external crystal and RTC for precise time base, time-of-day, calendar or task scheduling functions; Free running on-chip low power oscillator (1 kHz) for cyclic wake-up without external components Input/Output

· 53 general-purpose input/output (I/O) pins and 1 input-only pin

· 24 interrupt pins with selectable polarity on each pin.

· Hysteresis and configurable pull device on all input pins.

· Configurable slew rate and drive strength on all output pins.

Package Options

· 64-pin low-profile quad flat-pack (LQFP) — 10×10 mm

· 48-pin low-profile quad flat-pack (LQFP) — 7×7 mm

· 32-pin low-profile quad flat-pack (LQFP) — 7×7 mm