Break IC, Recover MCU, Microcontroller Reverse Engineering

Posts Tagged ‘copy microcontroller source dump’

Copy Microcontroller PIC12F675 Firmware

We can Copy Microcontroller PIC12F675 Firmware, please view below Microcontroller PIC12F675 features for your reference:

High-Performance RISC CPU:

· Only 35 Instructions to Learn

– All single-cycle instructions except branches

· Operating Speed:

– DC – 20 MHz oscillator/clock input

– DC – 200 ns instruction cycle

· Interrupt Capability

· 8-Level Deep Hardware Stack

· Direct, Indirect, and Relative Addressing modes

Special Microcontroller Features:

· Internal and External Oscillator Options

– Precision Internal 4 MHz oscillator factory calibrated to ±1%

– External Oscillator support for crystals and resonators

– 5 ms wake-up from Sleep, 3.0V, typical

· Power-Saving Sleep mode

· Wide Operating Voltage Range – 2.0V to 5.5V

· Industrial and Extended Temperature Range

· Low-Power Power-on Reset (POR)

· Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)

· Brown-out Detect (BOD)

· Watchdog Timer (WDT) with Independent

Oscillator for Reliable Operation

· Multiplexed MCLR/Input Pin

· Interrupt-on-Pin Change

· Individual Programmable Weak Pull-ups

· Programmable Code Protection

· High Endurance Flash/EEPROM Cell

– 100,000 write Flash endurance

– 1,000,000 write EEPROM endurance

– Flash/Data EEPROM Retention: > 40 years

Low-Power Features:

· Standby Current:

– 1 nA @ 2.0V, typical

· Operating Current:

– 8.5 mA @ 32 kHz, 2.0V, typical

– 100 mA @ 1 MHz, 2.0V, typical

· Watchdog Timer Current

– 300 nA @ 2.0V, typical

· Timer1 Oscillator Current:

– 4 mA @ 32 kHz, 2.0V, typical

Peripheral Features:

· 6 I/O Pins with Individual Direction Control

· High Current Sink/Source for Direct LED Drive

· Analog Comparator module with:

– One analog comparator

– Programmable on-chip comparator voltage reference (CVREF) module

– Programmable input multiplexing from device inputs

– Comparator output is externally accessible to Read MCU

· Analog-to-Digital Converter module (PIC12F675):

– 10-bit resolution

– Programmable 4-channel input

– Voltage reference input

· Timer0: 8-Bit Timer/Counter with 8-Bit Programmable Prescaler

· Enhanced Timer1:

– 16-bit timer/counter with prescaler

– External Gate Input mode

– Option to use OSC1 and OSC2 in LP mode as Timer1 oscillator, if INTOSC mode selected

· In-Circuit Serial ProgrammingTM (ICSPTM) via two pins

Copy Microcontroller AT89C51RE2 Binary

Copy Microcontroller AT89C51RE2 Binary from its flash and eeprom memory, then replicate the program and data to other blank MCU AT89C51RE2 for the same functions;

· 80C52 Compatible

– 8051 Instruction Compatible

– Four 8-bit I/O Ports (44 Pins Version)

– Three 16-bit Timer/Counters

– 256 bytes Scratch Pad RAM

– 11 Interrupt Sources With 4 Priority Levels if Copy Microcontroller

ISP (In-System Programming) Using Standard VCC Power Supply

Integrated Power Monitor (POR/PFD) to Supervise Internal Power Supply

Boot ROM Contains Serial Loader for In-System Programming

High-speed Architecture after Copy Microcontroller

– In Standard Mode:

40 MHz (Vcc 2.7V to 5.5V, Both Internal and External Code Execution)

60 MHz (Vcc 4.5V to 5.5V and Internal Code Execution Only)

– In X2 Mode (6 Clocks/Machine Cycle)

20 MHz (Vcc 2.7V to 5.5V, Both Internal and External Code Execution)

30 MHz (Vcc 4.5V to 5.5V and Internal Code Execution Only)

128K bytes On-chip Flash Program/Data Memory

– 128 bytes Page Write with auto-erase when Copy Microcontroller

– 100k Write Cycles

On-chip 8192 bytes Expanded RAM (XRAM)

– Software Selectable Size (0, 256, 512, 768, 1024, 1792, 2048, 4096, 8192 bytes)

Dual Data Pointer

Extended stack pointer to 512 bytes

Variable Length MOVX for Slow RAM/Peripherals

Improved X2 Mode with Independant Selection for CPU and Each Peripheral

Keyboard Interrupt Interface on Port 1

SPI Interface (Master/Slave Mode) after Copy Microcontroller

8-bit Clock Prescaler

Programmable Counter Array with:

– High Speed Output

– Compare/Capture

– Pulse Width Modulator

– Watchdog Timer Capabilities

Asynchronous Port Reset

Two Full Duplex Enhanced UART with Dedicated Internal Baud Rate Generator

Low EMI (inhibit ALE)

Hardware Watchdog Timer (One-time Enabled with Reset-Out), Power-Off Flag

Power Control Modes: Idle Mode, Power-down Mode

Power Supply: 2.7V to 5.5V when Copy Microcontroller

Temperature Ranges: Industrial (-40 to +85°C)

Packages: PLCC44, VQFP44