Break IC, Recover MCU, Microcontroller Reverse Engineering

Posts Tagged ‘copy microcontroller embedded software’

Copy Microcontroller P87C51X2BBD Binary from locked memory include flash and eeprom, remove the security fuse bit of MCU P87C51X2 by MCU Cracking technology and readout firmware from opened Microprocessor

Copy Microcontroller P87C51X2BBD Binary from locked memory include flash and eeprom, remove the security fuse bit of MCU P87C51X2 by MCU Cracking technology and readout firmware from opened Microprocessor;

FEATURES

· 80C51 Central Processing Unit

– 4 kbytes ROM/EPROM (P80/P87C51X2)

– 8 kbytes ROM/EPROM (P80/P87C52X2)

– 16 kbytes ROM/EPROM (P80/P87C54X2)

– 32 kbytes ROM/EPROM (P80/P87C58X2)

– 128 byte RAM (P80/P87C51X2 and P80C31X2)

– 256 byte RAM (P80/P87C52/54X2/58X2 and P80C32X2)

– Boolean processor

– Fully static operation

– Low voltage (2.7 V to 5.5 V at 16 MHz) operation

· 12-clock operation with selectable 6-clock operation (via software or via parallel programmer)

· Memory addressing capability

– Up to 64 kbytes ROM and 64 kbytes RAM

· Power control modes:

– Clock can be stopped and resumed

– Idle mode

– Power-down mode

· CMOS and TTL compatible

· Two speed ranges at VCC = 5 V

– 0 to 30 MHz with 6-clock operation

– 0 to 33 MHz with 12-clock operation

· PLCC, DIP, TSSOP or LQFP packages

· Extended temperature ranges

· Dual Data Pointers

· Security bits:

– ROM (2 bits)

– OTP (3 bits)

· Encryption array – 64 bytes

· Four interrupt priority levels

· Six interrupt sources

· Four 8-bit I/O ports

· Full-duplex enhanced UART

– Framing error detection

– Automatic address recognition

· Three 16-bit timers/counters T0, T1 (standard 80C51) and additional T2 (capture and compare)

· Programmable clock-out pin

· Asynchronous port reset

· Low EMI (inhibit ALE, slew rate controlled outputs, and 6-clock mode)

· Wake-up from Power Down by an external interrupt.

Circuit Engineering Company Limited continues to be recognized as the Southern China Leader in Services for IC Break, MCU recover, Chip Recover, Microcontroller Copy service. With the advancement of today’s modern circuit board technology, it is more important than ever to have specialists available to help you at a moment’s notice. Our engineering and commercial teams collectively have a vast amount of electronic experience covering field include Consumer Electronics, Industrial Automation Electronics, Wireless Communication Electronics., etc. For more information please contact us through email.

Copy Microcontroller PIC16F684 Firmware needs to unlock Microprocessor PIC16F684 security fuse bit, the silicon package can be removed by proper chemical solution, by focus ion beam will effectively modify the circuitry pattern of MCU PIC16F684

Copy Microcontroller PIC16F684 Firmware needs to unlock Microprocessor PIC16F684 security fuse bit, the silicon package can be removed by proper chemical solution, by focus ion beam will effectively modify the circuitry pattern of MCU PIC16F684;

High-Performance RISC CPU:

· Only 35 instructions to learn:

– All single-cycle instructions except branches

· Operating speed:

– DC – 20 MHz oscillator/clock input

– DC – 200 ns instruction cycle

· Interrupt capability

· 8-level deep hardware stack

Low-Power Features:

· Standby Current:

– 1 nA @ 2.0V, typical

· Operating Current:

– 8.5 µA @ 32 kHz, 2.0V, typical

– 100 µA @ 1 MHz, 2.0V, typical

· Watchdog Timer Current:

– 1 µA @ 2.0V, typical

· Direct, Indirect and Relative Addressing modes

Peripheral Features:

Special Microcontroller Features:

· Precision Internal Oscillator:

– Factory calibrated to ±1%

– Software selectable frequency range of 8 MHz to 31 kHz

– Software tunable

– Two-speed Start-up mode

– Crystal fail detect for critical applications

– Clock mode switching during operation for power savings

· Power-saving Sleep mode

· Wide operating voltage range (2.0V-5.5V)

· Industrial and Extended Temperature range

· Power-on Reset (POR)

· Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)

· Brown-out Detect (BOD) with software control option

· Enhanced low-current Watchdog Timer (WDT) with on-chip oscillator (software selectable nominal 268 seconds with full prescaler) with software enable;

· Multiplexed Master Clear with pull-up/input pin

· Programmable code protection

· High Endurance Flash/EEPROM cell:

– 100,000 write Flash endurance

– 1,000,000 write EEPROM endurance

– Flash/Data EEPROM retention: > 40 years

· 12 I/O pins with individual direction control:

– High current source/sink for direct LED drive

– Interrupt-on-pin change

– Individually programmable weak pull-ups

– Ultra Low-power Wake-up (ULPWU)

· Analog comparator module with:

– Two analog comparators

– Programmable on-chip voltage reference (CVREF) module (% of VDD)

– Comparator inputs and outputs externally accessible

· A/D Converter:

– 10-bit resolution and 8 channels

· Timer0: 8-bit timer/counter with 8-bit programmable prescaler· Enhanced Timer1:

– 16-bit timer/counter with prescaler

– External Gate Input mode

– Option to use OSC1 and OSC2 in LP mode as Timer1 oscillator if INTOSC mode selected

· Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler

· Enhanced Capture, Compare, PWM module:

– 16-bit Capture, max resolution 12.5 ns

– Compare, max resolution 200 ns

– 10-bit PWM with 1, 2 or 4 output channels, programmable “dead time”, max frequency 20 kHz

· In-Circuit Serial ProgrammingTM (ICSPTM) via two pins.