Break IC, Recover MCU, Microcontroller Reverse Engineering

Posts Tagged ‘copy mcu locked heximal’

Copy MCU XC18V04PC44C Program

We can Copy MCU XC18V04PC44C Program, please view below MCU XC18V04PC44C features for your reference:

XC18V00 Series In-System-Programmable Configuration PROMs:

Product Specification:

In-System Programmable 3.3V PROMs for Configuration of Xilinx FPGAs

♦ Endurance of 20,000 Program/Erase Cycles

♦ Program/Erase Over Full Industrial Voltage and Temperature Range (–40°C to +85°C)

IEEE Std 1149.1 Boundary-Scan (JTAG) Support

JTAG Command Initiation of Standard FPGA Configuration

Simple Interface to the FPGA

Cascadable for Storing Longer or Multiple Bitstreams

Low-Power Advanced CMOS FLASH Process Dual Configuration Modes

♦ Serial Slow/Fast Configuration (up to 33 MHz)

♦ Parallel (up to 264 Mb/s at 33 MHz)

5V-Tolerant I/O Pins Accept 5V, 3.3V and 2.5V Signals

3.3V or 2.5V Output Capability

Design Support Using the Xilinx ISE™ Foundation™ Software Packages

Available in PC20, SO20, PC44, and VQ44 Packages

Lead-Free (Pb-Free) Packaging

Description

Xilinx introduces the XC18V00 series of in-system programmable configuration PROMs (Figure 1). Devices in this 3.3V family include a 4-megabit, a 2-megabit, a 1-megabit, and a 512-kilobit PROM that provide an easy-to- use, cost-effective method for reprogramming and storing Xilinx FPGA configuration bitstreams. When the FPGA is in Master Serial mode, it generates a configuration clock that drives the PROM.

A short access time after CE and OE are enabled, data is available on the PROM DATA (D0) pin that is connected to the FPGA DIN pin. New data is available a short access time after each rising clock edge. The FPGA generates the appropriate number of clock pulses to complete the configuration. When the FPGA is in Slave Serial mode, the PROM and the FPGA are clocked by an external clock.

When the FPGA is in Master SelectMAP mode, the FPGA generates a configuration clock that drives the PROM. When the FPGA is in Slave Parallel or Slave SelectMAP mode, an external oscillator generates the configuration clock that drives the PROM and the FPGA.

After CE and OE are enabled, data is available on the PROM’s DATA (D0-D7) pins. New data is available a short access time after each rising clock edge. The data is clocked into the FPGA on the following rising edge of the CCLK. A free-running oscillator can be used in the Slave Parallel or Slave SelecMAP modes.

Multiple devices can be cascaded by using the CEO output to drive the CE input of the following device. The clock inputs and the DATA outputs of all PROMs in this chain are interconnected. All devices are compatible and can be cascaded with other members of the family or with the XC17V00 one-time programmable serial PROM family.

Copy MCU PIC32MX440F512H Binary and rewrite the firmware from master Microcontroller PIC32MX440F512H to blank new Microprocessor, decapsulate the MCU PIC32MX440F512H and get access to the databus is the first step of MCU cracking;

High-Performance 32-bit RISC CPU:

· MIPS32® M4K® 32-bit core with 5-stage pipeline

· 80 MHz maximum frequency

· 1.56 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state Flash access

· Single-cycle multiply and high-performance divide unit

· MIPS16e® mode for up to 40% smaller code size

· Two sets of 32 core register files (32-bit) to reduce interrupt latency

· Prefetch Cache module to speed execution

· Operating temperature range of -40ºC to +105ºC

· Operating voltage range of 2.3V to 3.6V

· 32K to 512K Flash memory (plus an additional 12 KB of boot Flash)

· 8K to 32K SRAM memory

· Pin-compatible with most PIC24/dsPIC® DSC devices

· Multiple power management modes

· Multiple interrupt vectors with individually programmable priority

· Fail-Safe Clock Monitor Mode

· Configurable Watchdog Timer with on-chip Low-Power RC Oscillator for reliable operation

Peripheral Features:

· Atomic SET, CLEAR and INVERT operation on select peripheral registers

· Up to 4-channel hardware DMA with automatic data size detection

· USB 2.0-compliant full-speed device and On-The-Go (OTG) controller

· USB has a dedicated DMA channel

· 3 MHz to 25 MHz crystal oscillator

· Internal 8 MHz and 32 kHz oscillators

· Separate PLLs for CPU and USB clocks

· Two I2C™ modules

· Two UART modules with:

– RS-232, RS-485 and LIN support

– IrDA® with on-chip hardware encoder and decoder

· Up to two SPI modules

· Parallel Master and Slave Port (PMP/PSP) with 8-bit and 16-bit data and up to 16 address lines

· Hardware Real-Time Clock and Calendar (RTCC)

· Five 16-bit Timers/Counters (two 16-bit pairs combine to create two 32-bit timers)

· Five capture inputs

· Five compare/PWM outputs

· Five external interrupt pins

· High-Speed I/O pins capable of toggling at up to 80 MHz

· High-current sink/source (18 mA/18 mA) on all I/O pins

· Configurable open-drain output on digital I/O pins

Debug Features:

· Two programming and debugging Interfaces:

– 2-wire interface with unintrusive access and real-time data exchange with application

– 4-wire MIPS® standard enhanced JTAG interface

· Unintrusive hardware-based instruction trace

· IEEE Standard 1149.2-compatible (JTAG) boundary scan

Analog Features:

· Up to 16-channel 10-bit Analog-to-Digital Converter:

– 1000 ksps conversion rate

– Conversion available during Sleep, Idle

· Two Analog Comparators