Copy AVR ATmega165A

We can Copy AVR ATmega165A, please view below the feature of AVR ATmega165A for your reference:

Features

High Performance, Low Power Atmel® AVR® 8-Bit Microcontroller

Advanced RISC Architecture

– 130 Powerful Instructions – Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 16MIPS Throughput at 16MHz (ATmega165PA/645P)

– Up to 20MIPS Throughput at 20MHz

(ATmega165A/325A/325PA/645A/3250A/3250PA/6450A/6450P)

– On-Chip 2-cycle Multiplier

High Endurance Non-volatile Memory segments

– In-System Self-programmable Flash Program Memory

· 16KBytes (ATmega165A/ATmega165PA)

· 32KBytes (ATmega325A/ATmega325PA/ATmega3250A/ATmega3250PA)

· 64KBytes (ATmega645A/ATmega645P/ATmega6450A/ATmega6450P)

– EEPROM

· 512Bytes (ATmega165A/ATmega165PA)

· 1Kbytes (ATmega325A/ATmega325PA/ATmega3250A/ATmega3250PA)

· 2Kbytes (ATmega645A/ATmega645P/ATmega6450A/ATmega6450P)

– Internal SRAM

· 1KBytes (ATmega165A/ATmega165PA)

· 2KBytes (ATmega325A/ATmega325PA/ATmega3250A/ATmega3250PA)

· 4KBytes (ATmega645A/ATmega645P/ATmega6450A/ATmega6450P)

– Write/Erase cycles: 10,000 Flash/100,000 EEPROM

– Data retention: 20 years at 85°C/100 years at 25°C(1)

– Optional Boot Code Section with Independent Lock Bits

· In-System Programming by On-chip Boot Program

· True Read-While-Write Operation

– Programming Lock for Software Security

– Capacitive touch buttons, sliders and wheels

– Up to 64 sense channels

JTAG (IEEE std. 1149.1 compliant) Interface

– Boundary-scan Capabilities According to the JTAG Standard

– Extensive On-chip Debug Support

– Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface

Peripheral Features

– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode

– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode

– Real Time Counter with Separate Oscillator

– Four PWM Channels

– 8-channel, 10-bit ADC

– Programmable Serial USART

– Master/Slave SPI Serial Interface

– Universal Serial Interface with Start Condition Detector

– Programmable Watchdog Timer with Separate On-chip Oscillator

– On-chip Analog Comparator

– Interrupt and Wake-up on Pin Change

Special Microcontroller Features

– Power-on Reset and Programmable Brown-out Detection

– Internal Calibrated Oscillator

– External and Internal Interrupt Sources

– Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby

I/O and Packages

– 54/69 Programmable I/O Lines

– 64/100-lead TQFP, 64-pad QFN/MLF and 64-pad DRQFN

Speed Grade:

– ATmega 165A/165PA/645A/645P: 0 – 16MHz @ 1.8 – 5.5V

– ATmega325A/325PA/3250A/3250PA/6450A/6450P: 0 – 20MHz @ 1.8 – 5.5V

Temperature range:

– -40°C to 85°C Industrial

Ultra-Low Power Consumption (picoPower devices)

– Active Mode:

· 1MHz, 1.8V: 215µA

· 32kHz, 1.8V: 8µA (including Oscillator)

– Power-down Mode: 0.1µA at 1.8V

– Power-save Mode: 0.6µA at 1.8V (Including 32kHz RTC over 20 years at 85°C or 100 years at 25°C