Break Chip PIC16F785 and readout the Heximal content from MCU PIC16F785, the fuse bit of microcontroller PIC16F785 will be unlocked for opening status;

High-Performance RISC CPU:

· Only 35 Instructions to Learn:

– All single-cycle instructions except branches

· Operating Speed:

– DC – 20 MHz oscillator/clock input

– DC – 200 ns instruction cycle

· Interrupt Capability

· 8-Level Seep Hardware Stack

· Direct, Indirect and Relative Addressing modes

Special Microcontroller Features:

· Precision Internal Oscillator:

– Factory calibrated to ±1%

– Software selectable frequency range of 8 MHz to 32 kHz

– Software tunable

– Two-Speed Start-up mode

– Crystal fail detect for critical applications

– Clock mode switching during operation for power savings after recover mcu p89lpc925fdh hex

· Power-Saving Sleep mode

· Wide Operating Voltage Range (2.0V-5.5V)

· Industrial and Extended Temperature Range

· Power-on Reset (POR)

· Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)

· Brown-out Reset (BOR) with Software Control Option

· Enhanced Low-Current Watchdog Timer (WDT) with on-chip Oscillator (software selectable nominal 268 seconds with full prescaler) with Software Enable

· Multiplexed Master Clear with Pull-up/Input Pin if break chip

· Programmable Code Protection

· High-Endurance Flash/EEPROM cell:

– 100,000 write Flash endurance

– 1,000,000 write EEPROM endurance

– Flash/Data EEPROM retention: > 40 years

Low-Power Features:

· Standby Current:

– 30 nA @ 2.0V, typical

· Operating Current:

– 8.5 ìA @ 32 kHz, 2.0V, typical

– 100 ìA @ 1 MHz, 2.0V, typical

· Watchdog Timer Current:

– 1 ìA @ 2.0V, typical

· Timer1 Oscillator Current:

– 2 ìA @ 32 kHz, 2.0V, typical

Peripheral Features:

· High-Speed Comparator module with:

– Two independent analog comparators

– Programmable on-chip voltage reference (CVREF) module (% of VDD) when break microcontroller pic12f629 program

– 1.2V band gap voltage reference

– Comparator inputs and outputs externally accessible

– < 40 ns propagation delay

– 2 mv offset, typical

· Operational Amplifier module with 2 independent Op Amps:

– 3 MHz GBWP, typical

– All I/O pins externally accessible

· Two-Phase Asynchronous Feedback PWM module:

– Complementary output with programmable dead band delay

– Infinite resolution analog duty cycle

– Sync Output/Input for multi-phase PWM

– FOSC/2 maximum PWM frequency

· A/D Converter:

– 10-bit resolution and 14 channels (2 internal)

· 17 I/O pins and 1 Input-only Pin:

– High-current source/sink for direct LED drive

– Interrupt-on-pin change

– Individually programmable weak pull-ups

· Timer0: 8-Bit Timer/Counter with 8-Bit Programmable Prescaler

· Enhanced Timer1:

– 16-bit timer/counter with prescaler

– External Gate Input mode

– Option to use OSC1 and OSC2 in LP mode as Timer1 oscillator, if INTOSC mode selected

· Timer2: 8-Bit Timer/Counter with 8-Bit Period Register, Prescaler and Postscaler for the purpose of break chip

· Capture, Compare, PWM module:

– 16-bit Capture, max resolution 12.5 ns

– Compare, max resolution 200 ns

– 10-bit PWM with 1 output channel, max frequency 20 kHz

· In-Circuit Serial ProgrammingTM (ICSPTM) via two pins

· Shunt Voltage Regulator (PIC16HV785 only):

– 5 volt regulation

– 4 mA to 50 mA shunt range

Comments are closed.